Geekcreit® DC12V 10A 1CH 433MHz Wireless Relay RF Remote Control Switch Receiver
186
Direct purchase from the factory 
Veilig betalen
Gratis cadeau
Verzendbeleid
RetourbeleidGratis Cadeau
Welkom bij Roymall, uw professionele cadeauwinkel. Wij waarderen uw steun en bieden als dank een gratis cadeau bij elke aankoop. Klaar om onze collectie te ontdekken? Blader door onze selectie, plaats uw bestelling en ontvang uw gratis cadeau.Verzendbeleid
Bestellingen worden binnen 2 werkdagen verwerkt. Bestellingen in het weekend worden de volgende werkdag verwerkt.Normale levertijd is 5-7 werkdagen.Levertijd kan variëren afhankelijk van bestemming.1. Retourbeleid
Wij accepteren alleen retouren van artikelen gekocht via roymall.com. Gratis cadeaus kunnen niet worden geretourneerd. Artikelen moeten ongebruikt en in originele verpakking zijn.Retouren worden binnen 3-5 werkdagen verwerkt na ontvangst.Aangepaste artikelen kunnen niet worden geretourneerd.Neem contact op: service@roymall.com of Whatsapp: +86193598494712.Restitutiebeleid
Volledige restitutie na ontvangst en controle. Verzendkosten worden niet terugbetaald.Neem contact op: service@roymall.com of Whatsapp: +8619359849471
>>>Click here to buy the remote control<<<
Specification:
1. Input Voltage: DC10-14V
2. Standby Current: <5MA
3. RF Frequency: 433MHZ
4. RF Working mode:Super heterodyne receiver
5. Receiver Sensitivity: >90dBm
6. Remote Control Distance: >100 meter(In open environment)
7. Decoding Way: MCU Software decoding
8. Can store the number of remote control:50
9. Support remote control type: Fixed code, learning code
10. Channel: 1CH
11. Multiple working modes: (Jog/Non-Latched ,inter-lock/Latched ,self-lock /Self-Latched,Delay off)
12. Wiring Method:Fixed wiring terminal
13. Working Voltage: DC12V
14. Output Current: 10A
15. Rated load:10A 250VAC / 10A 125VAC, 10A 30VDC / 10A 28VDC
16. Output:Normally open,Common,Normally closed
17. Dimension:3.5cm*3cm*1.6cm
Working/output way:
1.Jog: Press the learning button then release, set the mode from the system automatically working mode to action mode, wait for a while, when the board LED off, said it is into the learning state, press the remote control, the system received the signal. The LED flashes 5 times and goes off again. After 3S delay, LED light marked learning success, the system automatically withdraw from the learning state.
2.Self-locking: Press the learning button, then release, press 2 times, the system automatically set to self-locking mode, wait for a while, LED off, it is into the learning state, press the remote control, LED flash 5 times Off. 3S after the delay, LED light learning success.
3.Interlock: press the learning button, then release, press 3 times in succession, the system is set to interlock mode.
4.Delay: Press remote control relay pull-in,release the remote control and begin timekeeping,after 5s,10s,15s will automatically close the relay
Description:
1. Press the learning code .the indicator flash ,loosen your finger ,press any button of the remote control
the indicator flash 2 times and off .it mean you learn it successfully .
2. It can learn more than 12 PCS 2262 or 1527 chip with the different code wireless 433MHz remote control
3. Remove/clean :press the learning button about 8 seconds , the indicator turn on to off, it means the information that you keep have been removed successfully .
Package included:
1/2/3/5/10/20 x 12V 1CH 433MHz Wireless Relay Switch Receiver (optional)
Specification:
1. Input Voltage: DC10-14V
2. Standby Current: <5MA
3. RF Frequency: 433MHZ
4. RF Working mode:Super heterodyne receiver
5. Receiver Sensitivity: >90dBm
6. Remote Control Distance: >100 meter(In open environment)
7. Decoding Way: MCU Software decoding
8. Can store the number of remote control:50
9. Support remote control type: Fixed code, learning code
10. Channel: 1CH
11. Multiple working modes: (Jog/Non-Latched ,inter-lock/Latched ,self-lock /Self-Latched,Delay off)
12. Wiring Method:Fixed wiring terminal
13. Working Voltage: DC12V
14. Output Current: 10A
15. Rated load:10A 250VAC / 10A 125VAC, 10A 30VDC / 10A 28VDC
16. Output:Normally open,Common,Normally closed
17. Dimension:3.5cm*3cm*1.6cm
Working/output way:
1.Jog: Press the learning button then release, set the mode from the system automatically working mode to action mode, wait for a while, when the board LED off, said it is into the learning state, press the remote control, the system received the signal. The LED flashes 5 times and goes off again. After 3S delay, LED light marked learning success, the system automatically withdraw from the learning state.
2.Self-locking: Press the learning button, then release, press 2 times, the system automatically set to self-locking mode, wait for a while, LED off, it is into the learning state, press the remote control, LED flash 5 times Off. 3S after the delay, LED light learning success.
3.Interlock: press the learning button, then release, press 3 times in succession, the system is set to interlock mode.
4.Delay: Press remote control relay pull-in,release the remote control and begin timekeeping,after 5s,10s,15s will automatically close the relay
Description:
1. Press the learning code .the indicator flash ,loosen your finger ,press any button of the remote control
the indicator flash 2 times and off .it mean you learn it successfully .
2. It can learn more than 12 PCS 2262 or 1527 chip with the different code wireless 433MHz remote control
3. Remove/clean :press the learning button about 8 seconds , the indicator turn on to off, it means the information that you keep have been removed successfully .
Package included:
1/2/3/5/10/20 x 12V 1CH 433MHz Wireless Relay Switch Receiver (optional)
Products related to this item
Loading related products...
❮
❯
Videos for similar product
Loading product videos...
❮
❯
Electronics Ranking
